The Folding Safety Flag increases your visibility while you enjoy your mobility independence. The flag can be easily mounted to most scooters, manual wheelchairs, and power-chairs. When not in use, or when loading the scooter or wheelchair, the flag can be broken down and stowed. Large orange flag has a reflective strip for added safety. Safety Flag Features: Easily mounts to most scooters, manual wheelchairs, and powerchairs. Breaks down when not in use, or when getting in and out of vehicles. Safety Flag Specifications:Vinyl flag measures: 7 inches tall by 14.5 inches long.Fiberglass pole measures: 51 inches tall when fully extended.

The Telescoping Safety Flag increases your visibility while you enjoy your mobility independence. The flag can be easily mounted to most scooters, manual wheelchairs, and power-chairs. 

The Golden Technologies Embossed Folding Safety Flag increases your visibility while you enjoy your mobility independence. The flag can be easily mounted to most scooters, manual wheelchairs, and power-chairs if equipped with a receiver nib located on the anti-tip wheel in back or slide into the back seat pocket safety flag slot. When not in use, or when loading the scooter or wheelchair, the flag can be folded down below the individuals head. Large orange flag has a reflective strip for added safety.Folding Safety Flag Features:

The Scooter Walker Holder is a large pouch with straps that attaches to a scooter seat back for holding a basic style folding walker. This walker carrier is designed for stability on power mobility scooters or electric wheelchairs. People using a mobility scooter will find this walker holder allows them to easily carry a folding walker.To attach the walker holder to a scooter, slip the harness over the top of your seat back so that the fastening straps and bottom pocket hang from the seat back. Next, tighten the harness at the buckle. Place your folded walker down into the bottom pocket and then pull the fastening straps around your walker and buckle the straps. The Scooter Walker Holder is constructed of high quality water resistant fabric and is made in U.S.A. Scooter Walker Holder Features:Attaches to a scooter or electric wheelchair seat back.Securely holds a basic style folding walker.Scooter Walker Holder Specifications:Measures: 24 inches wide, 10 inches high, 3 inches deep.Material: High quality water resistant polyester.Made in: U.S.A.

The WeatherBreakerTM is a canopy that attaches to wheelchairs or scooters to protect you from the sun and rain and fits any wheelchair or scooter. The mounting kit will vary slightly depending on the make and model of your wheelchair or scooter. When you receive your canopy, it will include all the parts that you need to mount it to your vehicle. It will take you approximately 15-20 minutes to attach the two mounting poles to your wheelchair/scooter. These are black poles approximately 8" tall and less than an inch in width so they will not interfere with the normal operation of your wheelchair/scooter. Once the mounting poles are attached, then the canopy slips in and out. There are three models:.

The WeatherBreakerTM is a vented canopy that attaches to wheelchairs or scooters to protect you from the sun and rain and fits any wheelchair or scooter. The mounting kit will vary slightly depending on the make and model of your wheelchair or scooter. When you receive your canopy, it will include all the parts that you need to mount it to your vehicle. It will take you approximately 15-20 minutes to attach the two mounting poles to your wheelchair/scooter. These are black poles approximately 8" tall and less than an inch in width so they will not interfere with the normal operation of your wheelchair/scooter. Once the mounting poles are attached, then the canopy slips in and out. There are three models:.

The WeatherBreakerTM is a vented canopy that attaches to wheelchairs or scooters to protect you from the sun and rain and fits any wheelchair or scooter. The mounting kit will vary slightly depending on the make and model of your wheelchair or scooter. When you receive your canopy, it will include all the parts that you need to mount it to your vehicle. It will take you approximately 15-20 minutes to attach the two mounting poles to your wheelchair/scooter. These are black poles approximately 8" tall and less than an inch in width so they will not interfere with the normal operation of your wheelchair/scooter. Once the mounting poles are attached, then the canopy slips in and out. There are three models:.